修复你的物品 社区 商店

Xbox Series S Bluetooth Board Replacement

简介

Follow this guide to remove and replace the Bluetooth board from a Xbox Series S.

你所需要的

  1. Xbox Series S Bluetooth Board Replacement, Peel off the sticker coverings: 步骤 1 中的图像 1，3 Xbox Series S Bluetooth Board Replacement, Peel off the sticker coverings: 步骤 1 中的图像 2，3 Xbox Series S Bluetooth Board Replacement, Peel off the sticker coverings: 步骤 1 中的图像 3，3
    在这个步骤中使用的工具：
    Tweezers
    $4.99
    购买

    • Before you start this guide, turn off the Xbox and unplug any cables from it.

    • Use tweezers to peel off the two white screw covers located on the bottom corners of the back panel.

    编辑

  2. Xbox Series S Bluetooth Board Replacement, Remove the back panel screws: 步骤 2 中的图像 1，1
    在这个步骤中使用的工具：
    Magnetic Project Mat
    $19.95
    购买

    • Use a T8 Torx driver to remove the two 10 mm-long screws securing the back panel to the bottom panel.

    • Throughout this repair, keep track of each screw and make sure it goes back exactly where it came from.

    编辑

  3. Xbox Series S Bluetooth Board Replacement, Remove the bottom panel: 步骤 3 中的图像 1，3 Xbox Series S Bluetooth Board Replacement, Remove the bottom panel: 步骤 3 中的图像 2，3 Xbox Series S Bluetooth Board Replacement, Remove the bottom panel: 步骤 3 中的图像 3，3

    • Slide the bottom panel horizontally toward the back of the console until it comes to a stop.

    • This slides the clips out of the slots on the plastic case.

    • Lift straight up and remove the bottom panel from the plastic case.

    编辑

  5. Xbox Series S Bluetooth Board Replacement, Remove the plastic case screws: 步骤 4 中的图像 1，1

    • Use a T10 Torx driver to remove the seven 51 mm-long screws securing the chassis to the plastic case.

    编辑

  6. Xbox Series S Bluetooth Board Replacement, Remove the plastic case: 步骤 5 中的图像 1，3 Xbox Series S Bluetooth Board Replacement, Remove the plastic case: 步骤 5 中的图像 2，3 Xbox Series S Bluetooth Board Replacement, Remove the plastic case: 步骤 5 中的图像 3，3

    • With the bottom of the Xbox facing you, pull the two bottom-rear corners of the plastic case away from each other.

    • As you pull the corners apart, slide the back panel towards the bottom of the device. This releases the back panel from the plastic case.

    • The back panel should now settle on top of the clips on the back of the plastic case.

    • The back panel is permanently attached to the aluminum chassis.

    • Do not attempt to fully remove the chassis from the plastic case with this technique. You may risk breaking your case.

    编辑

  7. Xbox Series S Bluetooth Board Replacement: 步骤 6 中的图像 1，3 Xbox Series S Bluetooth Board Replacement: 步骤 6 中的图像 2，3 Xbox Series S Bluetooth Board Replacement: 步骤 6 中的图像 3，3

    • Pull the bottom-left corner away from the chassis while swinging the chassis away from the plastic case.

    • You may need to lift the chassis to free it from the clips on the bottom-front of the plastic case during this process.

    • Remove the plastic case from the chassis.

    编辑

  8. Xbox Series S Bluetooth Board Replacement, Remove the Bluetooth board: 步骤 7 中的图像 1，1

    • Use a T8 Torx driver to remove the three 9.5 mm-long screws securing the Bluetooth board to the long edge of the chassis.

    编辑

  9. Xbox Series S Bluetooth Board Replacement: 步骤 8 中的图像 1，3 Xbox Series S Bluetooth Board Replacement: 步骤 8 中的图像 2，3 Xbox Series S Bluetooth Board Replacement: 步骤 8 中的图像 3，3

    • Use a spudger to pry and loosen the Bluetooth board.

    • Do not pry from the bottom or sides of the Bluetooth board as it may bend the connector.

    • Pull the Bluetooth board straight out to disconnect it from the chassis.

    编辑
结论

To reassemble your device, follow these instructions in reverse order.

Take your e-waste to an R2 or e-Stewards certified recycler.

Repair didn’t go as planned? Try some basic troubleshooting, or ask our Answers community for help.

2等其他人完成本指南。

作者

与1其他贡献者

Robert Boyd

于02/01/21注册

30,881 声望

创作了94篇指南

徽章: 19

+ 16更多徽章

2指南评论

So I just followed the disassemble guide just to clean the dust out of my series s. When I reassembled the device the controllers were no longer synced and the sync button clicks as it should but it no longer syncing my controllers. I've tried with a cord and the sync then but once the cord is removed they go back to trying to sync and the button on the console is not activating. Do I need a new module

Shawn Wegner - 回复

Mind you everything else works the system starts up goes online and plays games

Shawn Wegner - 回复

添加评论

浏览统计数据:

过去 24 小时： 9

过去 7 天： 44

过去 30 天： 179

总计 6,465